Re: My printer is printing too high up the page. It cuts off a few inches at...
Since you already tried with different computers, I suggest you contact HP Support in your region for service options 1) Click on this link - www.hp.com/contacthp/ 2) Select your product type below....
View ArticleRe: HP Envy Pro 6400 series keeps going offline
In actual fact just realised the printer is in some kind of catatonic state - show the blue Wifi light and also a blue edge light but even lifting the lid does not wake the printer up - would normal...
View Articlevoert geen printopdrachten uit
Het betreft een HP ENVY 6010 en de printopdrachten blijven, na een 1e opdracht te hebben uitgevoerd, in de lijst staan. Alle mogelijke oplossingen met de print en scandoctor, en chat met HP leveren...
View ArticleMy hp photosmart printer won't turn off...back light on but no activity
My printer has back light on only.Wont set off or do anything. HAVE DONE ALL the troubleshooting suggestions. ANYBODY else have this problem or a suggestion?
View ArticleRe: voert geen printopdrachten uit
Hey Hope your doing fine! Thank you for visiting our English HP Support Community. We are only able to reply to posts written in English. To insure a quick response it would be advisable to post your...
View ArticleRe: 79 Service Error
I suggest we perform an NVRAM reset I have sent you a private message. Please check your Inbox Thank youIf the information I've provided was helpful, give us some reinforcement by clicking the...
View Articlecan not get brand new printer to recognize ink
Can not get new printer to recognize ink cartridge's.
View ArticlePrinter endlessly reboots
The printer keeps rebooting. It starts up, initializes, then appears to be ready to print/copy/whatever -- like you just pressed on the screen to wake it up. About 1 minute later, it reboots itself and...
View ArticleHP Envy 6000 not print on Lenovo Laptop
Hi,I am really hoping that someone can help.We have two Laptops, one is a HP and the other is a Lenovo.We have installed the HP ENvy 6000 on both Laptops using HP Smart and both say ready, however the...
View Article79 Error
It sounds like I have the same issue as everyone else over the past 2 days. System 79 Error and the printer keeps rebooting. I cannot hold it long enough to download any firmware. I have every...
View ArticleError 79 on HP LaserJet Pro MFP M426fdw
I have done my due diligence and researched this issue. So two days ago my MF printer started restarting without reason. Upon closer examination I noticed the "Error 79" before the restart. In my...
View ArticleService Error 79
Yesterday my printer started with the 79 service error. At first it happened every 5 minutes or so. When the error comes up it restarts by itself. Now it is basically stuck in a loop and showing the...
View ArticleRe: Error Code 0xb9808bf
, Welcome to HP Support Community! If you have already performed the steps from the document HP Inkjet Printers - '0xc19a0005' or Similar Error Code and the issue persists, it could be a hardware...
View ArticleRe: Service Error 79
To everyone having this problem - turn the computer off and on (to clear out the error) then once it goes to Ready, go to Setup, Service, RESTORE DEFAULTS. It worked for me!!!
View ArticleRe: Service Error 79
I have had this problem all day and have tried everything. if you can get your computer to the Ready screen long enough, go to Setup, Service and then RESTORE DEFAULTS. It worked and my computer is...
View ArticleRe: Service Error 79
I don't know, but I read a post further down and it suggested this with success, so i tried it and it worked. My computer is fine now. Must have been something with our same printer or a bad firmware...
View ArticleRe: HP Envy Pro 6400 series keeps going offline
I have the exact same issue with my new HP Envy Pro 6455. It will go catatonic when I haven't used it, then I have to unplug it to force a restart to get it working again. Very frustrating.
View ArticleRe: Printer constantly aligns
Hi @Dianamoon, I'd like to help! Let's try a power reset on the printer Reset the productWith the printer turned on, disconnect the power cord from the rear of the printer.Unplug the power cord from...
View Article